Aube-technologies TH135-02 Manual de usuario descargar pdf

TH135-02 400-135-005-B 11/12/06 1/3

CAUTION: To avoid electric shocks, deactivate your heating system at the

main electrical panel. Read the instructions carefully before disconnecting the

wires.

1.1 Installing a New Thermostat

For a new installation, select a position about 5 feet (1.5 m) above the floor,

where there is good air circulation. The thermostat must be installed on an

inside wall.

Avoid places where there are:

• air draughts (the top of a staircase, an air outlet,...)

• dead air spots (e.g., behind a door)

• direct sunlight

• chimneys or hidden pipes

1.2 Thermostat Installation

Remove the mounting plate from the thermostat.

n Loosen the screw holding the mounting plate to the

thermostat.

o Lift the lower part of the plate to remove it from the

thermostat.

p Loosen the screw holding the wire cover, and remove it.

q Secure the mounting plate to the wall and make the appropriate

connection (refer to section 2).

1.3 Wiring

Refer to the diagram. Connect one wire to either therminal and the other

wire to the other terminal.

Connection to a circulator

Connection to a boiler

o Put the wire cover back on.

NOTE: If you have a CT240 telephone controller, refer to section 5.1 for

hook-up.

Before installing the thermostat on the wall, it must be configured

using the dip switches at the back.

2.1 15- or 20-minute Cycles

The TH135 can operate on 15- or 20-minute

cycles. While 15-minute cycles provide

greater comfort, the heating system will be

running more often.

2.2 Temperature Control Modes

You can choose between two temperature

control modes:

Proportional Adaptive Mode

This mode analyses previous cycles in order to define the length of

the upcoming cycle. This mode guarantees optimal regulation of 3

cycles (switch #1 to 20 min.) or 4 cycles (switch #1 to 15 min.) per

hour, regardless of the season.

Ideal for:

• Radiant or convection electrical heating system

• Circulator control in a hot water system

Conventional Mode with Anticipation

This mode turns the system On or Off when the temperature reaches

preset levels. This mode is compatible with all heating systems. It is

recommended for a multi-zone system or when a thermostat directly

controls a furnace equipped with a combustion gas purge cycle of

more than 30 seconds.

Installation

Relay

Furnace

Thermostat Configuration

TH135-02

Installation and User Guide

Electronic Thermostat for Heating System

400-135-005-B (TH135-02 EU) ENG.fm Page 1 Monday, December 11, 2006 2:44 PM

1 2 3

Indice de contenidos

Pagina 1 - TH135-02

TH135-02 400-135-005-B 11/12/06 1/3CAUTION: To avoid electric shocks, deactivate your heating system at th

Pagina 2 - Battery Replacement

TH135-02 400-135-005-B 11/12/06 2/32.3 Pump ProtectionFor hot water installations, it is recommendedto act

Pagina 3 - Customer Assistance

TH135-02 400-135-005-B 11/12/06 3/3Power supply: 2 LR6 alkaline batteriesMax. resistive load: 5A @ 240 VAC

Comentarios a estos manuales

Sin comentarios

Aube-technologies TH135-02 Manual de usuario

Busca en linea o descarga Manual de usuario para Panel De Control Aube-technologies TH135-02. Aube Technologies TH135-02 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Panel De Control Aube-technologies TH135-02